• Capacity:  Adjustable  0-9 GPM (34,0 liters/min)
• Best choice for a roof cleaning pump
• 5 year manufacturer's warranty
• Maximum Temperature:  150 Deg. F  (66 Deg. C)      KE-038 -- 200 Deg. F (93 Deg. C)
• Maximum Air Pressure:  120 PSI (8,2 bar)
• Minimum Air Pressure:  20 PSI (1,3 bar)
• Dry Lift:  Models w/PTFE balls -- 10 ft. (3 meters)    
• Air Supply:  Inlet -- 1/4" NPT/BSP Female     
• Outlet -- 3/8" NPT/BSP Female  ***NOTE*** Muffler supplied
• Fluid Inlet/Discharge:  3/8" Pumps:  3/8" FNPT/BSP 1/2":  1/2" FNPT 
• Chemical Compatiblity of "A" with Sodium Hypochlorite and roof cleaning chemicals

(An Optional Dual Manifold can be added at any time.  Allows the pump to pull from two tanks or sources at the same time and mix at the pump.)


Pictured below is the REPAIR KIT for AFKE038-B3.

 

The Optional Dual Manifold can be retrofitted to your pump at any time.  The optional dual manifold added to the air diaphragm pump allows the pump to pull from two tanks or sources at the same time and mix at the pump.

 

MINI AIR FILTER / REGULATOR WITH PRESSURE GAUGE

• The All-Flo 3/8" KYNAR Air Diaphragm pump, AFKE038B3, is capable of handling highly corrosive chemicals as well as acids. 
• The 3/8" or 1/2" All-Flo air diaphragm pump is a perfect choice for residential and commercial cleaning.  It does not have to be rinsed after every use, has a 5 year warranty and will pay for itself and the gas powered air compressor in the amount of money saved on chemical conserved using the air diaphragm pump. 
• The user of most other pumps are forced into a larger nozzle orifice as with the 12 Volt pumps, gas powered diaphragm pumps like John Blue's, Udor's, Hypro's, etc.  A nozzle as small as a 1.5 or 2.0 may be used to apply the chemical instead of a 30 to 60 orifice. 
• Using a smaller nozzle will allow for greater control over chemical run-off (plant death and burns), minimizing the amount of waste product and procuring the proper disposal.  The use of an air diaphragm pump lowers chemical costs on each job and allows for greater profit.

The All-Flo 3/8" KYNAR Air Diaphragm pump, AFKE038B3, can be mounted on a stainless steel or aluminum mount to protect the body of the pump, allow easy access for maintenance and present your All-Flo in a professional manner.   A quick connect installed on the 1/4" red air hose will allow use of the air hose for other purposes such as filling  truck or trailer tires with an air valve, winterizing the All-Flo pump and related equipment or blowing off organic debris from a roof or driveway.  The air hose is a high quality 1/4" ID Parker rubber hose rated to 300 psi custom cut to the user's desired length.  PWP uses a hydraulic crimper to crimp the 1/4" mpt hose barbs on each end.   We prefer to offer our customers a hose assembly that will not require maintenance compared to when hose clamps are used with hose barbs.  Hose clamps loosen over time, rust and can become sharp.  Because the inlet port of the pump is 3/8", the general rule of pump plumbing indicates that the inner diameter of the supply line should be twice the inner diameter of the port and will require a minimum of a 3/4" ID Hose to supply the pump on the basis on flooded suction.  The 3/4" suction line should not collapse and should remain somewhat rigid but allow flexibility under pulsation.  Avoid using garden hose fittings on the suction side of any pump as they allow air to siphon into the suction side of the pump.  Do not 'hard plumb' a pump with PVC.


Diaphragm Pump Assemblies with Simple Systems or Single or Dual Tank Assemblies